Telephone 07502 392 882
email info@ducoheating.com
Embedded Files
System selection
Benefits of WARP Systems:
Fits in any living room, kitchen, bedroom and more without milling.
Thinnest waterborne system in heating and cooling on the market!
Very low construction height from 15mm inc mortar!
Closer heat to your feet! (use less energy)
75mm center to center tubing. Closest tubing on the market! (No cold spots)
Energy efficient: good for the environment and your wallet. (smaller tubes provide a higher pressure and a faster and more responsive system!)
Saves energy thanks to the fast response time.
Thin and light so ideal for renovation projects. (12.5mm tiles)
Easy and quick to install, within 1 day. (DIY friendly)
Suitable as main heating!
Can be connected to all heating and cooling sources. ONLY 30°C heat source input required!
Climate-conscious, future-proof and maintenance-free.
Space-saving and aesthetically pleasing.
Higher air quality and reduced allergens due to eliminating convective currents.
Free design layout plan
Find your ideal heating and cooling system.
Every situation in the search for a suitable system for underfloor heating, wall heating and ceiling heating (or cooling in combination with a heat pump) is unique.
For example, is it new construction or renovation?
Are you dealing with a maximum weight, limited installation height or other challenges in space?
Which screed or layer will be covered by the system?
Whatever questions you have for floor, wall or ceiling, our water-based systems offer the answer: they are suitable for every room and surface.
In addition, our systems are suitable as main heating.
You can choose from two different systems: SpeeTile and SpeeTherm.
Which system is right for my situation?
Dry construction or wet construction underfloor heating?
Dry construction or wet construction underfloor heating?
Which floor is suitable for which system?
Which floor is suitable for which system?
Heating systems are available in wet construction and dry construction systems.
In wet construction systems, the heating system is provided with screed filling compound. You can apply this to a concrete or stable wooden subfloor. If you then finish the floor with a floating, glued or poured finishing floor such as laminate, parquet, PVC, tiles or a cast floor, then a wet construction system such as SpeeTile is the right choice.
SpeeTherm is a dry construction system. With this system, you can lay a floating and rigid screed immediately after installation. Ideal if you want to install laminate, parquet or a duo plank. This system can be applied to concrete and (unstable) wooden subfloors.
Wet construction underfloor heating.
Underfloor heating with a minimum installation height.
SpeeTile is a 'wet construction system', which is finished with SpeeTop filling compound as a screed.
SpeeTile is a 'wet construction system', which is finished with SpeeTop filling compound as a screed.
With modular plastic mats, you can easily and quickly install the underfloor heating. Due to the patented click-break-slide system, there is no cutting loss and it always fits without measuring.
With modular plastic mats, you can easily and quickly install the underfloor heating. Due to the patented click-break-slide system, there is no cutting loss and it always fits without measuring.
You finish the floor with a floating, glued or poured finishing floor such as laminate, tiles, PVC or a cast floor.
You finish the floor with a floating, glued or poured finishing floor such as laminate, tiles, PVC or a cast floor.
Dry construction underfloor heating.
Underfloor heating for a floating and rigid screed floor.
SpeeTherm is a 'dry construction system', which is very suitable for laminate, parquet or a duo plank.
The loose, pre-formed 14mm EPS floor plates are placed directly on the surface, followed by 0.5mm Aluminum conductor plates.
After installing the underfloor heating and your finishing floor, you can use it immediately. A firing protocol is not necessary.
In combination with, for example, Fermacell dry screed overlay board, you can also install flexible floors such as PVC.
SpeeTile
SpeeTile
For all floating, glued and poured floors such as laminate, parquet, tiles, PVC or cast floors.
For all floating, glued and poured floors such as laminate, parquet, tiles, PVC or cast floors.
Suitable as main heating.
Easy installation with patented click-break-slide system.
Very low installation height from 15 mm.
Fast response time.
75mm center to center tubes.
Wet system with SpeeTop filling compound. The floor can be walked on after 4 hours.
Suitable as underfloor heating, wall heating and ceiling heating.
Can also be finished with stucco or clay plaster when used in walls or ceilings.
SpeeTherm
Suitable for floating and rigid floors such as laminate, parquet or duoplank.
Suitable as main heating.
No need for gluing and screwing.
Very low installation height from 15mm.
Fast response time.
100mm center to center tubes.
Dry construction system, can be used immediately after installation.
Suitable for direct finishing with floating, rigid finishing floors: laminate, parquet, duo plank.
Suitable for flat surfaces such as concrete or (unstable) wooden floors.
Finishing with flexible finishing floors (such as PVC or marmoleum is also possible in combination with a Fermacell Board.
1. Heating and cooling in new buildings.
Opt for future-proof and environmentally conscious.
When building a new building, it is smart to opt for a sustainable and future-proof system. In addition to underfloor heating, you can also opt for wall heating or ceiling heating. Whichever system you choose, it's set up in no time. Very handy when a lot of work has to be done in a short time!
When building a new building, it is smart to opt for a sustainable and future-proof system. In addition to underfloor heating, you can also opt for wall heating or ceiling heating. Whichever system you choose, it's set up in no time. Very handy when a lot of work has to be done in a short time!
2. Heating and cooling during renovation.
What is possible with your surface and construction height?
If you are going to work on a renovation or remodel, familiarize yourself in advance with the possibilities of heating and/or cooling the rooms you are tackling. Traditional underfloor heating is heavy and often has a high installation height, which is certainly not possible in every situation. Moreover, milling is not always possible, for example if you live in an apartment or your subfloor is not suitable for it. With our two versatile, complete and easy-to-use systems, we offer the solution.
If you are going to work on a renovation or remodel, familiarize yourself in advance with the possibilities of heating and/or cooling the rooms you are tackling. Traditional underfloor heating is heavy and often has a high installation height, which is certainly not possible in every situation. Moreover, milling is not always possible, for example if you live in an apartment or your subfloor is not suitable for it. With our two versatile, complete and easy-to-use systems, we offer the solution.
3. Heating and cooling when renovating a monumental building.
Preserve the characteristic elements and comply with regulations.
For historic buildings, it is good to heat evenly. This prevents changes in humidity from leading to cracks in the construction. It is better to choose underfloor, wall or ceiling heating than radiators. Nevertheless, the installation of such a system is an important point of attention for monumental buildings. You are often bound by strict rules during the entire renovation. Milling is often not allowed or simply not possible because of the wooden subfloors. Moreover, you can't just pour a thick layer of cement on wooden subfloors. With WARP Systems' systems, such challenges can be solved quickly and easily.
For historic buildings, it is good to heat evenly. This prevents changes in humidity from leading to cracks in the construction. It is better to choose underfloor, wall or ceiling heating than radiators. Nevertheless, the installation of such a system is an important point of attention for monumental buildings. You are often bound by strict rules during the entire renovation. Milling is often not allowed or simply not possible because of the wooden subfloors. Moreover, you can't just pour a thick layer of cement on wooden subfloors. With WARP Systems' systems, such challenges can be solved quickly and easily.
Tailor-made offer for your situation.
Characteristic of our system is the fast response time. The same goes for our colleagues: receive your quote within 1 working day.
WARP Systems for all your questions:
Need wall, ceiling or underfloor heating advice? We like to make it easy for you, so feel free to ask your questions to one of our specialists.
07502 392 882
info@ducoheating.com
Page updated
Google Sites
Report abuse